Plancha - ignition

How do I start my Verycook plancha?

Installation of the Verycook plancha

Take out your Verycook plancha from its packaging and get a screw-in gas hose (type G1/2-G1/4) for Butane or Propane gas).

At the rear left of the Verycook plancha is the gas connection nozzle. Screw the silver/golden end of the gas hose to the griddle and the other end of the gas hose to the regulator of the gas bottle.

Place the grill plate on your plancha-grill.

Defuse the safety of the regulator on the gas bottle and open the gas valve on the regulator.

Then press one of the two buttons of the plancha and press at the same time a few seconds on the piezo button on the right to create the spark.

The flame comes on, release the button after a few seconds. You can use your Verycook plancha!


How do I check the correct functioning of my plancha Creative electronic piezo ignition?

Checking the correct functioning of your electronic piezo ignition:

1) You should hear a "tac-tac-tac" or "tic-tic-tic" sound when you press the piezo-ignition button on your plancha. If you do not hear the "Tac-Tac-Tac" or "Tic-Tic-Tic", read the following article: How do I change the piezo ignition of my plancha grill?

2) Remove the grill plate, press the piezo ignition button on your plancha, check the presence of the spark on the end of the piezocable, near the affected burner.

Piezo électronique plancha gaz

3) Use a pair of pliers to guide the tip of the piezo cable closer to the burner.

Cable piezzo pour plancha


How do I change the housing of the piezo ignition of my Plancha Grill Creative?

We will show you how to change the electronic piezo ignition housing of your plancha gas grill. However, this need rarely occurs.

First of all, check whether the battery of the piezo case has been replaced (see article: How do I replace the piezo ignition of my plancha?) Steps to change the piezo housing of your plancha:

1) Unscrew the 4 screws on each side of your plancha Creative. Remove the front buttons from your plancha by pulling them out horizontally forwards.

Retirer habillage plancha

Retirer bouton plancha

2) First unscrew the red piezo button on the front of the plancha and then unscrew the black plastic ring.

3) Turn over the plancha heating core and then remove the two sleeves of the piezocable from the black plastic housing.

Retirer piezzo plancha

The housing can now be removed and replaced.

Boitier piezo plancha

Follow the steps in reverse order to install the new housing.


How do I change the battery of my Plancha Creative piezo ignition?

The Piezo ignition system of your Plancha Creative works with a classic LR6 (AA) battery.

It is possible that the battery of the piezo ignition of your plancha has to be replaced.

1) You can unscrew the black and red plastic button directly from the front.

2) Inside is the battery which has to be replaced. The + is on the front, against the black and red plastic button, which you can then screw back.

Changer pile piezzo plancha


How can I check the correct setting of the safety thermocouple valve?

The adjustment of the valve may affect the proper functioning of the safety thermocouple. To check its correct setting, follow these steps:

1) Pull the control knob of the plancha towards you to remove it from its axis.

Valve plancha gaz

2) Once the button is removed, you will see the control screw to the left of the knob

Valve plancha à régler

3) Using a screwdriver, carefully tighten the screw clockwise until it stops.

Reglage valve gaz plancha

4) Now screw it a quarter turn counterclockwise looser.

Regler valve plancha au gaz


The burners of my plancha Creative do not burn properly, what can I do?

The Verycook plancha Creative has two chrome U-shaped burners.

To solve this problem, please read the corresponding article about the problem you have.

> I can ignite my burner

  

> I can not light my burner


How can I check the correct tightening of the safety thermocouple?

The safety thermocouple system is a safeguard that is present on all Verycook planchas and makes it possible to stop the gas supply automatically when the flame of one of the burners of the plancha goes out. The correct connection of the thermocouple can be checked by the following steps:

1) Remove the grill plate and turn over the plancha.

2) A copper cable is screwed onto the valve of the plancha. Check that the cable is screwed tight as shown in the following photo.


The flames of my plancha grill are yellow, how can I fix this?

Two effective solutions to improve the flame quality of your plancha grill:

1. Clean the burners (if I have had my plancha grill for at least a few months, otherwise go to step 2):

2. Adjust the air supply : the air/gas mixture ensures good combustion and a blue flame. This setting can be adjusted.


How to change the piezo ignition battery on my Simplicity plancha grill?

1) Remove the hob and turn the heating core over from your plancha grill.

2) Unscrew the black cap from the black piezo box on the right side of your plancha grill.

3) Remove the battery and replace it with a new one. If you have a 2-burner plancha grill you must use an LR3 or AAA battery, if you have a 3-burner plancha grill you must use an LR6 or AA battery.


The burners on my Simplicity plancha grill no longer light up, what should I do?

The Verycook Simplicity 2 or 3 burners plancha grill is composed of two stainless steel round burners.

In order to solve this, please consult the article that relates to the problem you are experiencing.

> I can ignite my burner

  

> I can't ignite my burner


Comment changer l'allumage Piezo de votre plancha Simplicity ?

1) Retirer la plaque de cuisson et retourner le coeur de chauffe de votre plancha 2) Dévisser le capuchon du boîtier piezo ainsi que l'écrou en plastique 3) Retirer mes 4 (plancha 2 feux) ou 6 (plancha 3 feux) cosses des câbles piezo du boîtier en plastique noir 4) Retirer le boîtier électronique noir et rebrancher les câbles sur le nouveau boîtier.


Comment régler l'intensité des flammes de votre plancha Créative ?

Nous allons vous montrer la démarche à suivre pour régler l'intensité des flammes de votre plancha. 1) Retirer la plaque de cuisson et retourner me coeur de chauffe de votre plancha. x 2) Dévisser la bague de serrage argentée à l'extrémité du brûleur. x Attention ! : Plus vous ouvrez l'air, plus la combustion pourra se faire et plus la flamme sera bleue.


Comment régler l'intensité des flammes d'un brûleur de votre plancha Simplicity ?

Nous allons vous montre la démarche à suivre pour régler l'intensité des flammes des flammes de votre plancha. 1) Retirer la plaque de cuisson et retourner le coeur de chauffe de votre plancha. x 2) Dévisser la vis de serrage située sur le collier. x 3) Jouer sur l'ouverture d'air pour régler l'intensité des flammes du brûleur. x 4) Visser la is de serrage pour bloquer l'ouverture d'air. x Attention ! : Plus vous ouvrez l'air, plus la combustion pourra se faire et plus la flemme sera bleue.